Specifications |
N/A
Airbus AIMS 04-04-003, AIMS 04-04-040 , AIMS 04-04-041, AIMS 04-04-064, ABP 4-2130, ASNA 5148, PQ No. 10050 - 240-01 Dassault: DGQT 1.7.0.0120 Product information mentioned in the technical datasheet is given for information purposes and can differ from requirements of specifications above. In that case, customer requirements are valid for your application. |
Instructions for Use (Spray Application) |
N/A
Mixing ratio by weight - Base 100 Mixing ratio by volume - Base 2 V Mixing ratio by weight - Hardener / Catalyst 43 Mixing ratio by volume - Hardener / Catalyst 1 V Mixing ratio by weight - Water 110 to 150 Mixing ratio by volume - Water 3 V to 4 V Mixing Procedure Ideally, the unmixed products should be stored between 18ºC (64ºF) and 25ºC (77ºF) for 24 hours before use. The F70-A base should be mixed for 10 minutes in a pneumatic or oscillating mixer before use. Mix the base and the hardener until the mixture is homogenous before adding demineralized water in two stages. The mixture must be made at a temperature between 15ºC (59ºF) and 35ºC (95ºF). Sieve the paint through a 80-150 µm (3.1-6.0 mils) filter. Never add additional water once the paint mixture has been made.. Induction Time - None Spraying viscosity at 20ºC / 68ºF - (CA 4) 4 V 20 ± 3s Spraying viscosity at 20ºC / 68ºF - (ISO 4) 4 V 33 ± 4s Spraying viscosity at 20ºC / 68ºF - (Zahn 2) 4 V 22 ± 3s Pot Life - 8 hours (dilution 4 V) Note The pot life depends on the dilution ratio. The paint viscosity may vary depending on the temperature and increase over the pot life. The water used to dilute the paint should be demineralised. Depending on the material used and the application temperature, the dilution may vary between 3 V and 4 V of demineralised water. A 3 V dilution of demineralised water is recommended for the white tints application. Viscosities mentioned above are corresponding to the recommended range of viscosity to ensure compliant application. The range of dilution must be used to adjust viscosity to reach the recommended one. Water based paints show a thixotropic behaviour. This implies that efflux time can vary according different parameters such as: type of mixing, mixing quantity, dilution, temperature, time between mixing and viscosity measurement ISO 4 cup is the reference cup. The others are give for information purposes |
Instructions for Use (Brush Application) |
N/A
Mixing ratio by weight - Base 100 Mixing ratio by volume - Base 2 V Mixing ratio by weight - Hardener / Catalyst 42 Mixing ratio by volume - Hardener / Catalyst 1 V Mixing ratio by weight - Water 0 V or from 35 to 50 Mixing ratio by volume - Water0 V or of 1 V in 1.5 Mixing Procedure Remove the safety ring and press down on the cap to release the F70-A hardener. Shake the container for approximately 1 minute. Remove the cap to be able to apply the F70-A topcoat with a suitable brush. If the material after shaking of 1min is not homogenious please use a stick for futher mixing (around 1 min) until the material is homogen. Do not hermetically close TUK after mixing base and hardener. Induction Time - In case of dilution, wait 3 minutes before adding demineralized water Pot Life - 2 hours undiluted Note - Spray with dry, oil-free air. |
Theoretical Coverage for 25 Microns (µm) (1 Mils) Dry (Base and Undiluted Hardener) |
N/A 23 m²/L937 ft²/gal |
Dry Film Weight |
N/A 1.5 g/m² |
Volatile Organic Compounds (VOC) Volume as Per International Organization for Standardization (ISO 11890-1) |
N/A 186 g/L1.55 lb/gal |
Volatile Organic Compounds (VOC) Volume as Per American Society for Testing and Materials (ASTM D 3960) |
N/A 397 g/L3.31 lb/gal |
Color |
N/A Gray BAC 707 (M9001) Gray FS26251 NORMDEF 2625 White Dassault 001 White Dassault 0036 |
Shelf Life/Storage |
N/A 18 months for the base and hardener stored between 5°C and 35°C (41°F and 95°F) and in full and sealed original packaging. 12 months for Touch-Up Kits stored between 5°C and 35°C (41°F and 95°F) in full and sealed original packaging |
Gloss Level |
N/A Above 50 GU at 60° |
Note |
N/A Gloss levels have been determined using glossmeter with an angle of incidence of 60°. The theorical consumption value doesn't take into account the transfer efficiency for spray application |
Dust Free Dry Time at 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature |
N/A 2 hour |
Dust Free Dry Time at 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature |
N/A 40 minutes |
Dust Free Dry Time at 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature |
N/A 5 minutes |
Recoatable Dry Time at 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature |
N/A 5 minutes to 72 hours |
Recoatable Dry Time at 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature |
N/A 5 minutes to 90 minutes |
Recoatable Dry Time at 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature |
N/A 5 minutes to 25 minutes |
Note for Drying Times |
N/A
Drying times have been determined using test pieces of a thickness < 2 mm and for 20 µm (0.8 mils) of dry film. Before accelerated drying = 70°C (158°F), leave to flash off for at least 15 minutes at room temperature. To recoat F70-A top coat with another product, contact us. For the F70-A top coat infrared drying, contact us. MEK Resistance: After 10 hours at 23°c |
Surface Preparation |
N/A
Top coat F70-A should be applied on Mapaero P60-A primer. See recoating time recommended on the P60-A primer technical data sheet. All recommendations mentioned above are given for information. |
Temperature Condition |
N/A 15 to 35 ºC59 to 95 ºF |
Relative Humidity Condition |
N/A 20 to 85 % |
Equipment |
N/A Gravity compressed air gun Nozzle 0.8 mm to 1.8 mm |
Dry Film Thickness |
N/A 20 to 30 µm0.8 to 1.2 mil |
Wet Film Thickness |
N/A 55 to 85 µm2.2 to 303 mil |
Number of Coats |
N/A
Apply several coats to achieve 20 µm to 30 µm (0.8 to 1.2 mils) dry thickness. The number of coats depends on the size and the shape of the part to which it is being applied. The recommended dynamic air pressure is 1.5 bar to 4 bar (22 to 58 psi). |
Equipment Cleaning |
N/A Clean the equipment with a suitable cleaning solvent such as Mapaero D760, Mapaero D770-B aqueous cleaning solvent can also be used for cleaning the ready-to-use mixture. |
Dry to Handle Dry Time at 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature |
N/A 3 hours 30 |
Dry to Handle Dry Time at 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature |
N/A 1 hour |
Dry to Handle Dry Time at 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature |
N/A 7 minutes |
Dry to Tape Dry Time at 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature |
N/A 3 hours 45 |
Dry to Tape Dry Time at 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature |
N/A 1 hour 15 |
Dry to Tape Dry Time at 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature |
N/A 10 minutes |
Fully Cured Dry Time at 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature |
N/A 3 days |
Fully Cured Dry Time at 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature |
N/A 90 minutes |
Fully Cured Dry Time at 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature |
N/A 25 minutes |
Defects and Corrections |
N/A
In the event of a defect, contact your Quality Department. In case of low thickness: Apply a thin coat of F70-A to achieve the desired thickness. If the above recommended recoating time is exceeded, reactivate with a Scotch-Brite type. In case of thick coats: Contact you Quality Department. If there are micro-bubbles, running, rejects or numerous inclusions: Reactivate the surface using an abrasive paper (grade 220 to 320), remove the dust then clean the surface using an approved cleaning product. Apply a thin coat of F70-A to achieve the required thickness. In case of significant defects: Remove the F70-A primer with an approved chemical paint remover or make a selective stripping to the P60-A primer. A surface treatment and the P60- A primer application sould be done once again in case the substrate is exposed. |
Packing |
N/A
The F70-A base is available in 4 kg and 200 kg. The hardener is available in 2 L and 200 L. Kits are also available:
|
Warranty |
N/A We guarantee our products against hidden defaults over material and preparation. Our Responsibility is limited to the obligation of freely replacing the defective material without there being a claim for any compensation. The advice we give is based on our experience but it might not be absolutely right. Consequently this does not imply our responsibility in case of inefficiency. Furthermore our company cannot be responsible for any material or corporal damages caused due to a misuse or mishandling of our products. Any concession to these clauses, to be valid, must be an official document issued by our offices and signed by our direction. |
