| Items |
 /Asset/Mapaero-Chemical-Resistant-Coatings.jpg P60-A 160 Grams Per Liter (g/L) Volatile Organic Compound (VOC) Epoxy Primer |
/Asset/Mapaero-Chemical-Resistant-Coatings.jpg P65-C2K 130 Grams Per Liter (g/L) Volatile Organic Compound (VOC) Primer |
/Asset/Mapaero-Chemical-Resistant-Coatings.jpg P65-HG 130 Grams Per Liter (g/L) Volatile Organic Compound (VOC) Primer |
/Asset/Mapaero-Chemical-Resistant-Coatings.jpg SP350 285 Grams Per Liter (g/L) Volatile Organic Compound (VOC) Primer |
/Asset/Mapaero-Chemical-Resistant-Coatings.jpg P60-2K 160 Grams Per Liter (g/L) Volatile Organic Compound (VOC) Primer |
|||||
| Description | Strontium chromate-based, three-component water-reducible epoxy primer, with high chemical resistance. This product is designed for the protection of metallic structures on aircraft. P60-A primer is recommended for use in combination with Mapaero F70-A structural topcoat. |
Chromate-free water-based epoxy primer two component. P65-C2K primer is used on composite structures to guarantee their protection. Coatings for Aircraft Structure Protection |
Chromate-free water-based epoxy high gloss primer three component. P65-HG primer is used on composite structures to reveal the defects (porosity, scratches…) and to guarantee their protection. This primer can be used in combination with M50 filler/putty from MAPAERO. Coatings for Aircraft Structure Protection |
Chromate free high solid epoxy primer three component used for corrosion protection, SP350 is used to protect aircraft metallic parts. This product has good adhesion and chemical resistance properties, especially on aluminium alloys. SP350 can be used with AkzoNobel high solid polyurethane topcoat XS420. | Strontium chromate-based, two component water-reducible epoxy primer, with high chemical resistance. | |||||
| Base | P60-A Base | P65-C2K | P65-HG | SP350 Base | ||||||
| Original Equipment Manufacturer (OEM) Specifications | Embraer MEP 10-059 TY III | |||||||||
| Volatile Organic Compounds for ASTM (American Society for Testing and Materials) | 340 g/L | |||||||||
| Volatile Organic Compounds ISO (International Organization for Standardization) | 160 g/L | |||||||||
| Test Method for Volatile Organic Compounds (VOC) | ASTM D3960 ISO11890-1 | |||||||||
| Primer Type | Epoxy | |||||||||
| Industry Standards | ||||||||||
| Brands | AkzoNobel | |||||||||
| Type | ||||||||||
| Hardener / Catalyst | H2K | H88 | ||||||||
| Hardener | P60-A Hardener | SP350 Hardener | ||||||||
| Thinner | Demineralized Water | Water (AIMS 09-00-003 grades A, B and C) | SP350 PLUS Thinner | |||||||
| Qualified Product List |
Airbus Canada - A2MS 565-001 Grade B Category 1,Type I & Category 2, Type I Airbus - 04JMD9 Airbus - 04QAB2 Airbus - 04QAC2 Airbus - A2MS 565-007 Ty E Class 2 Semi-Gloss (White FS 27875 and Dark Gray FS26473) Airbus - ABP 4-1123 Airbus - AIMS 04-04-001 Airbus - AIMS 04-04-003 Airbus - AIMS 04-04-004 Airbus - AIMS 04-04-038 Airbus - AIMS 04-04-040 Airbus - AIMS 04-04-041 Airbus - AIMS 04-04-042 Airbus - AIMS 04-04-063 Airbus - ASNA 5147, PQ N° 10050-230-01 Airbus - CML 16-063, 04DEB2 Airbus - IPS 04-04-038-07 Bombardier - BAMS 565-001 Grade B Category 1,Type I & Category 2, Type I Dassault - DGQT 1.7.0.0120 Embraer - MEP 10-59 type III Viking - VAMS 565-001 Grade B Category 1,Type I & Category 2, Type I Product specifications are constantly changing, to ensure the most accurate information regarding specifications. |
Safran Aircraft Engines - DMR74-130 Safran Landing Systems - IFC30-125-06 Safran Nacelles - HMRC0149A Product specifications are constantly changing, to ensure the most accurate information regarding specifications. |
||||||||
| Surface Preparation |
P60-A primer is used particularly on aluminium alloys that have had the following treatments: Alodine 1200: Cr6 conversion CAA: Chromic Acid Anodising SAA: Sulphuric Acid Anodising TSA: Tartaric Sulphuric Anodising BAA: Boric Acid Anodising Observe the recoating time between the surface treatment and painting. This may vary depending on the treatment and industrial instructions. Contact us for information on uses on other metallic structures, surface treatments or paints. P60-A primer can also be used on sealants. All recommendations mentioned above are given for information. |
P65-C2K primer can be applied directly on composite parts, suitably degreased and sanded. All recommendations mentioned above are given for information. |
P65-HG primer can be applied directly on composite pieces, suitably degreased and sanded with a Scotch Brite paper. It can be applied on M50 filler/putty, previously sanded according to the product technical data sheet. All recommendations mentioned above are given for information. |
SP350 primer should be applied on aluminium alloys with following surface treatments :
For Open time information and cleaning process prior to paint application, please contact your quality department Contact us for information on uses on other substrate or surface treatments. In the event of a defect, contact your Quality Department. |
||||||
| Specifications |
Qualified in accordance with: EMBRAER : MEP 10-133, MEP 10-118 Product information mentioned in the technical datasheet is given for information purposes and can differ from requirements of specifications above. In that case, customer requirements are valid for your application. |
Qualified in accordance with: Airbus: AIMS 04-04-050 Product information mentioned in the technical datasheet is given for information purposes and can differ from requirements of specifications above. In that case, customer requirements are valid for your application. |
||||||||
| Theoretical Coverage | ||||||||||
| Theoretical Coverage for 50 Microns (µm) (2 Mils) Dry (Base and Hardener Undiluted) | ||||||||||
| Theoretical Coverage for 25 Microns (µm) (1 Mils) Dry (Base and Hardener Undiluted) | ||||||||||
| Theoretical Coverage for 20 Microns (µm) (0.8 Mils) Dry | 20 m²/L815 ft²/gal | 23 m²/L937 ft²/gal | ||||||||
| Dry Film Weight | 1.7 g/m² | 1.5 g/m² | 1.60 g/m² | 1.4 g/m² | ||||||
| Volatile Organic Compounds (VOC) Volume as Per International Organization for Standardization (ISO 11890-1) | 130 g/L | 130 g/L | ||||||||
| Volatile Organic Compounds (VOC) Volume as Per American Society for Testing and Materials (ASTM D 3960) | 250 g/L | 250 g/L | ||||||||
| Color | RAL6021 Green | Beige RAL1001 | Beige RAL1001 | Beige | Green | |||||
| Shelf Life/Storage | 12 months for the base and hardener, stored between 5ºC and 35ºC (41ºF and 95ºF) in full and sealed original packaging. |
12 months for the base and hardener, stored between 5°C and 35°C (41°F and 95°F) and in full and sealed original packaging. 6 months, stored in Touch-Up Kit stored between 5°C and 35°C (41°F and 95°F) in full and sealed original packaging |
||||||||
| Gloss Level | 80 GU at 60º | >= 70 GU at 60° | ||||||||
| Note | Gloss levels have been determined using glossmeter with an angle of incidence of 60º. The theorical consumption value doesn’t take into account the transfer efficiency for spray application |
Gloss levels have been determined using glossmeter with an angle of incidence of 60º. The theorical consumption value doesn’t take into account the transfer efficiency for spray application |
||||||||
| Instructions for Use (Spray Application) |
Mixing ratio by weight - Base 100 Mixing ratio by volume - Base 4 V Mixing ratio by weight - Hardener / Catalyst 24 Mixing ratio by volume - Hardener / Catalyst 1 V Mixing Procedure - Ideally, the unmixed products should be stored between 18ºC and 25ºC (64ºF and 77ºF) for 24 hours before use. The P65-C2K should be mixed for 5 to 10 minutes in a pneumatic or oscillating mixer before use. Mix the base and the hardener until the mixture is homogeneous. The mixing must be made at a temperature between 15ºC (59ºF) and 35ºC (95ºF). Sieve the paint through a 120-150 µm (4.5-6.0 mils) filter. Induction Time - None Spraying viscosity at 20ºC / 68ºF (Zahn 2 Cup) - 18 to 25s Pot Life - 4 hours Note The paint viscosity may vary depending on the temperature and increase over the pot life. Viscosities mentioned above are corresponding to the recommended range of viscosity to ensure compliant application. The range of dilution must be used to adjust |
Mixing ratio by weight - Base 100 Mixing ratio by volume - Base 2 V Mixing ratio by weight - Hardener / Catalyst 43 Mixing ratio by volume - Hardener / Catalyst 1 V Mixing ratio by weight - Water 50 to 60 Mixing ratio by volume - Water 1.3 V to 1.6 Mixing Procedure Ideally, the unmixed products should be stored between 18ºC and 25ºC (64ºF and 77ºF) for 24 hours before use. The P65-HG should be mixed for 10 minutes in a pneumatic or oscillating mixer before use. Mix the base and the hardener until the mixture is homogeneous before adding demineralized water. The mixture must be made at a temperature between 15ºC (59ºF) and 35ºC (95ºF). Sieve the paint through a 120-150 µm (4.7-5.9 mils) filter. Never add additional water once the paint mixture has been made. Induction Time - None Spraying viscosity at 20ºC / 68ºF - (ISO 4) 1.4 V 43 ± 6s Spraying viscosity at 20ºC / 68ºF - (CA 4) 1.4 V 20 ± 3s Pot Life - 3 hours for a 1.4 V dilution Note Pot life depends on the dilution ratio. The paint viscosity may vary depending on the temperature and increase over the pot life. For an application with a two-component mixing machine, it is possible to mix first 2 volumes of base P65-HG with 1 volume of demineralized water. The following mix has to be done: Pre-mix base + 3V of water (This pre-mix can be stored 1 month between 5 ºC et 35 ºC or 41ºF and 95ºF). Hardener : 1V. Final performances of the product remain unchanged compared to the 3-components mixture. Viscosities mentioned above are corresponding to the recommended range of viscosity to ensure compliant application. The range of dilution must be used to adjust viscosity to reach the recommended one Water based paints show a thixotropic behavior. This implies that efflux time can vary according different parameters such as: type of mixing, mixing quantity, dilution, temperature, time between mixing and viscosity measurement ISO 4 cup is the reference cup. The others are given for information purpose. |
||||||||
| Instructions for Use (Brush Application) |
Mixing ratio by weight - Base 100 Mixing ratio by volume - Base 4 V Mixing ratio by weight - Hardener / Catalyst 24 Mixing ratio by volume - Hardener / Catalyst 1 V Mixing Procedure - Mix the base and hardener in proportions indicated above until the mixture is completely homogeneous. Induction Time - None Pot Life - 4 hours |
Mixing ratio by weight - Base 100 Mixing ratio by volume - Base 2 V Mixing ratio by weight - Hardener / Catalyst 43 Mixing ratio by volume - Hardener / Catalyst 1 V Induction Time - None Pot Life - 2 hours undiluted |
||||||||
| Temperature Condition | 15 to 35 ºC60 to 95 ºF | 15 to 35 ºC59 to 95 ºF | ||||||||
| Relative Humidity Condition | 20 to 85 % | 20 to 85 % | ||||||||
| Equipment | Gravity compressed air gun Nozzle 1 mm to 1.8 mm | Gravity compressed air gun Nozzle 1 mm to 1.8 mm | ||||||||
| Equipment Type | ||||||||||
| Dry Film Thickness | 15 to 25 µm0.6 to 1 mil | 15 to 25 µm0.6 to 1 mil | ||||||||
| Wet Film Thickness | 20 to 45 µm0.8 to 1.8 mil | 20 to 45 µm0.8 to 1.8 mil | ||||||||
| Number of Coats with a Brush (Fine Hairs) | ||||||||||
| Equipment Cleaning | Clean the equipment with a suitable cleaning solvent such as Mapaero D760. Mapaero D770-B aqueous cleaning solvent can also be used. | Clean the equipment with a suitable cleaning solvent such as Mapaero D760. Mapaero D770-B aqueous cleaning solvent can also be used. | ||||||||
| Number of Coats |
Apply several coats to achieve 15 to 25 µm (0.6 to 1 mils) dry thickness. The number of coats depends on the size and the shape of the part to which it is being applied. The recommended dynamic air pressure is 1.5 bar to 4 bar (22 to 58 psi). |
Apply 1 crossed coat to achieve a 15 µm to 25 µm (0.6 to 1 mil) dry thickness. Each coat has to be wet and of the same thickness. The number of coats depends on the size and the shape of the part to be painted. The recommended dynamic air pressure is 2 bar to 4 bar (30 to 60 psi). |
Apply 1 crossed coat to achieve a 15 µm to 25 µm (0.6 to 1 mil) dry thickness. Each coat has to be wet and of the same thickness. The number of coats depends on the size and the shape of the part to be painted. The recommended dynamic air pressure is 2 bar to 4 bar (29 to 58 psi). |
With air spray gun, apply 1 wet coat to achieve 15 µm to 35 µm (0.6 to 1.4 mils) dry thickness. The number of coats depends on the size and the shape of the part on which it is being applied. The recommended dynamic air pressure is 1.5 bar to 4 bar (22 to 58 psi). | ||||||
| Note for Application Recommendations | Spray with dry, oil-free air. | Spray with dry, oil-free air. | ||||||||
| Dust Free Dry Time at 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature | 10 minutes | 2 hour | ||||||||
| Dust Free Dry Time at 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature | 5 minutes | 45 minutes | ||||||||
| Dust Free Drying Time at 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature | 5 minutes | |||||||||
| Dry to Sand Dry Time at 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature | ||||||||||
| Dry to Sand Dry Time at 40 Degree Celsius (ºC) (104 Degree Fahrenheit (ºF)) Temperature | ||||||||||
| Dry to Sand Dry Time at 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature | ||||||||||
| Dry to Sand Dry Time at 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature | ||||||||||
| Dry to Handle Drying Time at 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature | 5 hour | 7 hour | ||||||||
| Dry to Handle Drying Time at 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature | 45 minutes | 1 hour 15 Minutes | ||||||||
| Dry to Handle Drying Time at 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature | 10 minutes | 20 minutes | ||||||||
| Dry to Tape Drying Time at 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature | 6 hour | |||||||||
| Dry to Tape Drying Time at 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature | 50 minutes | |||||||||
| Dry to Tape Drying Time at 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature | 15 minutes | |||||||||
| Recoatable Drying Time at 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature | 10 minutes to 3 days | 2 hours to 168 hours | ||||||||
| Recoatable Drying Time at 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature | 10 minutes to 2 hours | 45 minutes to 2 hours | ||||||||
| Recoatable Drying Time at 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature | 5 minutes to 35 minutes | 5 minutes to 45 minutes | ||||||||
| Fully Cured Drying Time at 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature | 3 days | 7 days | ||||||||
| Fully Cured Dry Time at 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature | ||||||||||
| Fully Cured Dry Time at 40 Degree Celsius (ºC) (104 Degree Fahrenheit (ºF)) Temperature | 4 days | |||||||||
| Fully Cured Dry Time at 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature | 2 hours 30 | 2 hour | 3 hour | |||||||
| Fully Cured Dry Time at 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature | ||||||||||
| Fully Cured Dry Time at 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature | 1 hour | 45 minutes | 1.5 hour | |||||||
| Note for Drying Times |
Wet on Wet application: P60-A / F70-A system can be used wet on wet. At room temperature, leave P60-A primer flash off for 15 minutes in the spray booth and then recover with F70-A topcoat. MEK resistance: After 23 hours at room temperature or 1 hour at 60°C, P60-A primer can be cleaned with MEK solvent. Before accelerated drying = 70°C, leave to flash off for at least 15 minutes at room temperature. Recoating P60-A primer with another topcoat (Epoxy or Polyurethane) is possible. For process optimization, please contact us. Drying P60-A primer with Infra Red is possible. For process optimization, please contact us. Drying times have been determined using test pieces of a thickness < 2 mm and for 15 µm (0.6 mils) of dry film. |
Drying times have been determined using test pieces of 1 mm thickness, with a 20 µm (0.8 mils) dry film. Before accelerated drying = 70ºC (158ºF), let it flash off for at least 15 minutes at room temperature. Parts whose drying was forced must cool down to below 35 ºC (95ºF) before proceeding to the next step. To recoat P65-C2K primer with another product/primer, contact us. For the P65-C2K primer infrared drying, contact us. Drying time and temperature (evaporation and curing) are given for information only and may vary depending on humidity, the shape, the nature of the workpiece and the thickness of the paint. |
SP350 primer must be cured at minimum 40°C (104°F) before applying XS420 TopcoatDrying times have been determined using test plates of a thickness < 2 mm and for 20 µm (0.8 mils) of dry film. Before accelerated drying = 70°C (158°F), leave to flash off for at least 15 minutes at room temperature. The "recoatable" time is determined with XS420 top coat.To recoat SP350 with other waterborne or solvent-based paints, contact us.The qualification test was performed at 23°C (73°F) ± 2°C/35°F for fully cured in 7 days. |
|||||||
| Spray Application |
P60-A Base : Volume - 2 parts, Weight - 100 parts P60-A Hardener : Volume - 1 part, Weight - 38 parts Demineralized Water : Volume - 2 to 4 parts, Weight - 65 to 130 parts The water used to dilute the paint should be demineralized with a conductivity < 25 µSiemens. Mixing procedure Ideally, the unmixed products should be stored between 18°C and 25°C (64°F and 77°F) for 24 hours before use.
|
|||||||||
| Initial Spraying Viscosity (20 Degree Celsius (ºC) / 68 Degree Fahrenheit (ºF) Temperature) |
The dilution is determined depending on the equipment that will be used for application The list below is a guide to the optimum viscosity for various types of equipment. Air gun - 18+/-3sCA4 Electrostatic spray gun - 18+/-3 sCA4 Pressurized pot - 21 +1-3 sCA4 Automatic Pump - 21 +1-3 sCA4 Mixing machine - 23+/-3 sCA4 Viscosities mentioned above correspond to the recommended range of viscosity to ensure compliant application. The range of dilution must be used to adjust viscosity to reach the recommended one. Viscosity values are given ± 3sec for CA4 Cup and ± 4sec for the others. Water reducible paints show a thixotropic behaviour. This implies that efflux time can vary according to different parameters such as: type of mixing, mixing quantity, dilution, temperature, time between mixing and viscosity measurement. |
|||||||||
| Dilution rate in Volume at 2.0 V (Cup CA4) | 27 | |||||||||
| Dilution rate in Volume at 2.0 V (ISO 4) | 65 | |||||||||
| Dilution rate in Volume at 2.0 V (Zahn2) | 44 | |||||||||
| Dilution rate in Volume at 2.5 V (Cup CA4) | 19 | |||||||||
| Dilution rate in Volume at 2.5 V (ISO 4) | 38 | |||||||||
| Dilution rate in Volume at 2.5 V (Zahn2) | 23 | |||||||||
| Dilution rate in Volume at 3.0 V (Cup CA4) | 18 | |||||||||
| Dilution rate in Volume at 3.0 V (ISO 4) | 26 | |||||||||
| Dilution rate in Volume at 3.0 V (Zahn2) | 23 | |||||||||
| Dilution rate in Volume at 3.5 V (Cup CA4) | 16 | |||||||||
| Dilution rate in Volume at 3.5 V (ISO 4) | 24 | |||||||||
| Dilution rate in Volume at 3.5 V (Zahn2) | 20 | |||||||||
| Dilution rate in Volume at 4.0 V (Cup CA4) | 14 | |||||||||
| Dilution rate in Volume at 4.0 V (ISO 4) | 20 | |||||||||
| Dilution rate in Volume at 4.0 V (Zahn2) | 18 | |||||||||
| Note for Initial Spraying Viscosity (20 Degree Celsius (ºC) / 68 Degree Fahrenheit (ºF) Temperature) |
ISO 4 cup is the reference cup. The others are given for information. Viscosity measurements are provided as guidelines only and are not to be used as quality control parameters. Certified information is provided by certification documentation available on request. |
|||||||||
| Pot Life at 20 Degree Celsius (ºC) / 68 Degree Fahrenheit (ºF) Temperature | 8 hours for a 4 V dilution. | |||||||||
| Note for Pot Life at 20 Degree Celsius (ºC) / 68 Degree Fahrenheit (ºF) Temperature | Pot life depends on the dilution ratio. The paint viscosity may vary depending on the temperature and increases over the pot life. Depending on the flow cup used and the application temperature, the dilution may vary between 2 V and 4 V of demineralized water. | |||||||||
| Dry Film Thickness (DFT) for Initial Spraying Viscosity 20 Degree Celsius (ºC) / 68 Degree Fahrenheit (ºF) Temperature | 15 to 25 µm0.6 to 1 mil | |||||||||
| Wet Film Thickness (WFT) for Initial Spraying Viscosity 20 Degree Celsius (ºC) / 68 Degree Fahrenheit (ºF) Temperature1 | 50 to 80 µm2 to 3.1 mil | |||||||||
| Brush Application (Mix Ratio) |
P60-A Base : Volume - 2 parts, Weight - 100 parts P60-A Hardener : Volume - 1 parts, Weight - 38 parts Demineralized Water : Volume - 0 or 1 to 1.5 parts, Weight - 0 or 35 to 50 parts Remove the safety ring and press down on the cap to release the P60-A hardener. Shake the container for approximately 1 minute. Remove the cap to be able to apply the P60-A primer with a suitable brush. If the material is not homogeneous after 1 min. shaking, please use a stick for further mixing (around 1 Min.) until the material is homogeneous. Do not hermetically close TUK after mixing base and hardener. |
SP350 Base : Volume - 8 parts, Weight - 100 parts SP350 Hardener : Volume - 1 part, Weight - 11 parts Mixing Procedure Remove the safety ring and press down on the cap to release the SP350 hardener. Shake the container for approximately 1 min. Remove the cap to be able to apply the SP350 primer with a suitable brush. If the material is not homogenous after 1 min shaking, please use a stick for further mixing (around 1 min) until the material is homogeneous. Do not hermetically close TUKS after mixing base and hardener. |
||||||||
| Note for Brush Application (Mix Ratio) | When diluting, wait 3 minutes before adding demineralized water. | |||||||||
| Pot Life | 2 hours not diluted | |||||||||
| Dry Film Thickness (DFT) for Brush Application (Mix Ratio) | 15 to 25 µm0.6 to 1 mil | 15 to 35 µm0.6 to 1.4 mil | ||||||||
| Wet Film Thickness (WFT) for Brush Application (Mix Ratio) | 50 to 80 µm2 to 3.1 mil | 20 to 50 µm0.8 to 2 mil | ||||||||
| Note for Wet Film Thickness (WFT) | Wet film thickness correspond to 3V dilution. | |||||||||
| Temperature | 15 to 35 ºC59 to 95 ºF | 15 to 59 ºC35 to 95 ºF | ||||||||
| Relative Humidity | 20 to 85 % | 30 to 85 % | ||||||||
| Conditions | Primer P60-A may be applied in conditions outside the limits shown above. However, it is recommended to be careful to ensure a satisfactory result. Please contact your local AkzoNobel Aerospace Coatings representative to determine the appropriate application techniques when environmental conditions are outside of the recommended range. | PRIMER SP350 may be applied in conditions outside of the limits shown above. Application must be done carefully to ensure a satisfactory result. Please contact your local AkzoNobel Aerospace Coatings representative to determine the appropriate application techniques when environmental conditions are outside of the recommended range. | ||||||||
| Equipment Recommendation |
Gravity compressed air gun - Nozzle 0.8 to 1.8 mm Electrostatic spray gun - Nozzle 0.8 to 1.4 mm |
Gravity compressed air gun - Nozzle 0.8 mm to 1.8 mm. | ||||||||
| Note for Number of Coats |
Defects and Corrections: In the event of a defect, contact your Quality Department. In case of too low thickness: Apply a thin coat of P60-Ato achieve the required thickness. If the above recommended recoating time is exceeded, reactivate with an abrasive pad. For too thick coats: Contact your Quality Department. If there are micro-bubbles, runs, fish-eyes or numerous inclusions: Reactivate the surface using a abrasive paper (grade 220 to 320), remove the dust then clean the surface using an approved cleaning product. Apply a thin coat of P60-A to achieve the required thickness. If there are significant defects: Remove the P60-A primer with an approved chemical paint stripper or remove using a plastic medium (in this case, the surface treatment has to be redone). |
If the thickness is too low:Apply a thin coat to obtain the desired thickness while respecting the recoating time. If the recoating time is exceeded, reactivate with an abrasive pad such as Scotch-Brite type A. If the thickness is too high:See your quality department. For micro-bubbles, runs or fish-eyes (depending on instructions given and type of part):Reactivate the surface using an abrasive paper grade 220 to 320, remove the dust and clean the surface using an approved cleaning solvent, apply a thin coat. In case of big default, non-conformity:Strip the part with an approved paint stripper (only on simple part) or strip by sand blasting (in this case, the surface treatment must be repeated). |
||||||||
| Cleaning of Equipment | Clean the equipment with a suitable cleaning solvent such as Mapaero D760. | Clean equipment with a suitable solvent such as Mapaero D713 or D760. Dispose of waste in accordance with regulations. | ||||||||
| Note for Cleaning of Equipment | Spray with dry, oil-free air. |
Spray with dry and oil-free air. The use of thinner SP350 Plus is highly recommended. |
||||||||
| Dry to Handle Dry Time for 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature | 35 minutes | |||||||||
| Dry to Handle Dry Time for 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature | 15 minutes | |||||||||
| Dry to Handle Dry Time for 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature | 5 minutes | |||||||||
| Dry to Tape Dry Time for 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature | 1 hour 45 min | |||||||||
| Dry to Tape Dry Time for 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature | 30 minutes | |||||||||
| Dry to Tape Dry Time for 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature | 15 minutes | |||||||||
| Dry to Sand Dry Time for 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature | 1 hour | |||||||||
| Dry to Sand Dry Time for 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature | 30 minutes | |||||||||
| Dry to Sand Dry Time for 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature | 15 minutes | |||||||||
| Recoatable Dry Time for 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature | 15 min to 120 hour | |||||||||
| Recoatable Dry Time for 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature | 5 min to 2 hour | |||||||||
| Recoatable Dry Time for 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature | 5 min to 35 min | |||||||||
| Full Cure Dry Time for 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature | 3 days | |||||||||
| Full Cure Dry Time for 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature | 2 hour | |||||||||
| Full Cure Dry Time for 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature | 35 minutes | |||||||||
| Theoretical Coverage for 15 Microns (µm) (0.6 Mils) Dry (Base and Not Diluted Hardener) | 37 m²/L15 ft²/gal | |||||||||
| Minimum Gloss at 60 Degree | 20 GU | |||||||||
| Note for Minimum Gloss at 60 Degree | Gloss levels have been determined using glossmeter with an angle of incidence of 60°. The theoretical consumption value doesn’t take into account the transfer efficiency for spray application. | |||||||||
| Storage | Store the product dry and at a temperature between 5 and 35ºC / 41 and 95ºF per AkzoNobel Aerospace Coatings specification. Store in the original unopened containers. Storage temperature and shelf life may vary per OEM specification requirements. Refer to the container label for specific storage life information. | Store the product dry and at a temperature between 5 and 35ºC / 41 and 95ºF per AkzoNobel Aerospace Coatings specification. Store in the original unopened containers. Storage temperature and shelf life may vary per OEM specification requirements. Refer to the container label for specific storage life information. | ||||||||
| Shelf Life | 12 months in Touch-Up Kits, stored between 5°C and 35°C (41°F and 95°F) in full and sealed original packaging. | |||||||||
| Shelf Life at 5 to 35 Degree Celsius (ºC)(41 to 95 Degree Fahrenheit (ºF)) Temperature |
P60-A Base - 18 months P60-A Hardener - 18 months |
SP350 Base - 12 months SP350 Hardener - 12 months SP350 PLUS Thinner - 48 months |
||||||||
| Spray Application (Mix Ratio) |
SP350 Base : Volume - 8 parts, Weight - 100 parts SP350 Hardener : Volume - 1 parts, Weight - 11 parts SP350 PLUS Thinner : Volume - 0 to 1 parts, Weight - 0 to 10 parts Mixing Procedure The use of SP350 Plus thinner is highly recommended. Ideally, the unmixed products should be stored between 18°C (64°F) and 25°C (77°F) for 24 hours before use.
We recommend use of ratio by weight for mixing. Every opened can has a limited life. Packaging must be well closed and stored in suitable conditions. |
|||||||||
| Initial Spraying Viscosity (20 Degree Celsius (ºC) (68 Degree Fahrenheit (ºF)) Temperature |
With Dilution - Ratio 8V/1V/1V 23 ± 3ºC (73 ± 40F) CA 4 ISO 4 15 ± 3s 20 ± 4s |
|||||||||
| Note for Initial Spraying Viscosity (20 Degree Celsius (ºC) (68 Degree Fahrenheit (ºF)) Temperature |
Viscosities mentioned above correspond to the recommended range of viscosity to ensure compliant application. The range of dilution can be used to adjust viscosity to the desired level. ISO 4 cup is the reference cup. The others are given for information purposes. Viscosity measurements are provided as guidelines only and are not to be used as quality control parameters. Certified information is provided by certification documentation available on request. |
|||||||||
| Pot Life (20 Degree Celsius (ºC) (68 Degree Fahrenheit (ºF)) Temperature |
3 hours between 15°C (59°F) and 30°C (86°F) 1 hour between 30°C (86°F) and 35° (95°F) |
|||||||||
| Note for Pot Life (20 Degree Celsius (ºC) (68 Degree Fahrenheit (ºF)) Temperature | To prevent drying on the surface of the mixed pot, cover it for the duration of the pot life. | |||||||||
| Dry Film Thickness (DFT) for Initial Spraying Viscosity (20 Degree Celsius (ºC) (68 Degree Fahrenheit (ºF)) Temperature | 15 to 35 µm0.6 to 1.4 mil | |||||||||
| Wet Film Thickness (WFT) for Initial Spraying Viscosity (20 Degree Celsius (ºC) (68 Degree Fahrenheit (ºF)) Temperature | 20 to 50 µm0.8 to 2 mil | |||||||||
| Pot Life at (20 Degree Celsius (ºC) (68 Degree Fahrenheit (ºF)) Temperature |
3 hours between 15°C (59°F) and 30°C (86°F) 1 hour between 30°C (86°F) and 35° (95°F) |
|||||||||
| Dry to Handle Dry Time at 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) ± 2 Degree Celsius (ºC) / 35 Degree Fahrenheit (ºF) Temperature | 6 hour | |||||||||
| Dry to Handle Dry Time at 40 Degree Celsius (ºC) (104 Degree Fahrenheit (ºF)) Temperature | 2 to 3 hour | |||||||||
| Dry to Handle Dry Time at 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature | 1 to 1.5 hour | |||||||||
| Dry to Handle Dry Time at 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature | 30 to 45 minutes | |||||||||
| Dry to Handle Dry Time for InfraRed | 25 ± 5 minutes | |||||||||
| Dry to Tape Dry Time at 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) ± 2 Degree Celsius (ºC) / 35 Degree Fahrenheit (ºF) Temperature | 6 to 7 hour | |||||||||
| Dry to Tape Dry Time at 40 Degree Celsius (ºC) (104 Degree Fahrenheit (ºF)) Temperature | 2 to 3 hour | |||||||||
| Dry to Tape Dry Time at 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature | 1.5 to 2 hour | |||||||||
| Dry to Tape Dry Time at 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature | 45 to 60 minutes | |||||||||
| Dry to Tape Dry Time for InfraRed | 30 ± 10 minutes | |||||||||
| Recoatable Dry Time at 40 Degree Celsius (ºC) (104 Degree Fahrenheit (ºF)) Temperature | 1.5 to 8 hour | |||||||||
| Recoatable Dry Time at 60 Degree Celsius (ºC) (140 Degree Fahrenheit (ºF)) Temperature | 30 mins to 2.5 hrs | |||||||||
| Recoatable Dry Time at 80 Degree Celsius (ºC) (176 Degree Fahrenheit (ºF)) Temperature | 15 to 75 minutes | |||||||||
| Recoatable Dry Time for InfraRed | 10 ± 35 minutes | |||||||||
| Fully Cured Dry Time at 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) ± 2 Degree Celsius (ºC) / 35 Degree Fahrenheit (ºF) Temperature | 7 days | |||||||||
| Fully Cured Dry Time for InfraRed | 40 ± 10 minutes | |||||||||
| Theoretical Coverage for 25 Microns (µm) (1 Mils) Dry Undiluted2 | 25 m²/L1019 ft²/gal | |||||||||
| Volatile Organic Compounds (VOC) Volume as Per International Organization for Standardization (ISO 11890-1) Base and Hardener Undiluted. | 285 g/L | |||||||||
| Volatile Organic Compounds (VOC) Volume as Per American Society for Testing and Materials (ASTM D 3960) Base and Hardener Undiluted | 2.4 lb/gal | |||||||||
| Gloss at 60 Degree | 20 to 80 GU | |||||||||
| Note for Gloss at 60 Degree | Gloss levels have been determined using glossmeter with an angle of incidence of 60°. | |||||||||
| Note for Dry Times |
Drying times have been determined using test pieces of 1 mm thickness, with a 20 µm (0.8 mils) dry film. Before accelerated drying 70ºC (158ºF), let it flash off for at least 15 minutes at room temperature. Parts whose drying was forced must cool down to below 35 ºC (95ºF) before proceeding to the next step. To recoat P65-HG primer with another product/primer, contact us. For the P65-HG primer infrared drying, contact us. Drying time and temperature (evaporation and curing) are given for information only and may vary depending on humidity, the shape and the material of the workpiece and the thickness of the paint. |
|||||||||
| Defects and Corrections |
In the event of a defect, contact your Quality Department. For a dry thickness < 15µm (0.6 mils): Apply a thin layer to obtain the right thickness. If the recoating time is exceeded, reactivate with a Scotch-Brite type® A. If there are micro-bubbles, running, rejects or numerous inclusions: Reactivate slightly, using an abrasive paper grade P240 or P320. Remove dust using a suitable cloth and apply a thin coat of primer, as described above. |
In the event of a defect, contact your Quality Department. For a dry thickness < 15µm (0.6 mils): Apply a thin layer to obtain the right thickness. If the recoating time is exceeded, reactivate with a Scotch-Brite type® A. If there are micro-bubbles, running, rejects or numerous inclusions: Reactivate slightly, using an abrasive paper grade P240 or P320. Remove dust using a suitable cloth and apply a thin coat of primer, as described above. |
||||||||
| Packing | The P65-C2K is available in 5L (4L base and 1L hardener) |
The base P65-HG is available in 4 L and 200 L. The hardener H88 is available in 2 L and 200 L. 45 ml Touch-Up Kits (TUK) (30 ml P65-HG + 15 ml H88 Hardener) |
||||||||
| Warranty | We guarantee our products against hidden defaults over material and preparation. Our Responsibility is limited to the obligation of freely replacing the defective material without there being a claim for any compensation. The advice we give is based on our experience but it might not be absolutely right. Consequently this does not imply our responsibility in case of inefficiency. Furthermore our company cannot be responsible for any material or corporal damages caused due to a misuse or mishandling of our products. Any concession to these clauses, to be valid, must be an official document issued by our offices and signed by our direction. | We guarantee our products against hidden defaults over material and preparation. Our Responsibility is limited to the obligation of freely replacing the defective material without there being a claim for any compensation. The advice we give is based on our experience but it might not be absolutely right. Consequently this does not imply our responsibility in case of inefficiency. Furthermore our company cannot be responsible for any material or corporal damages caused due to a misuse or mishandling of our products. Any concession to these clauses, to be valid, must be an official document issued by our offices and signed by our direction. | ||||||||
| Applications | ||||||||||
| Safety Precautions | Comply with all local safety, disposal and transportation regulations. Check the Material Safety Data Sheet (MSDS)and label of the individual products carefully before using the products. The MSDS’s are available on request. | Comply with all local safety, disposal and transportation regulations. Check the Material Safety DataSheet (MSDS) and label of the individual products carefully before using the products. The MSDS’sare available on request. | Comply with all local safety, disposal and transportation regulations. Check the Material Safety Data Sheet (MSDS)and label of the individual products carefully before using the products. The MSDS’s are available on request. | |||||||
| Important Note | The information in this data sheet is not intended to be exhaustive and is based on the present state of our knowledge and on current laws: any personusing the product for any purpose other than that specifically recommended in the technical data sheet without first obtaining written confirmation from us asto the suitability of the product for the intended purpose does so at his own risk. It is always the responsibility of the user to take all necessary steps to fulfillthe demands set out in the local rules and legislation. Always read the Material Data Sheet and the Technical Data Sheet for this product if available. Alladvice we give or any statement made about the product by us (whether in this data sheet or otherwise) is correct to the best of our knowledge but we haveno control over the quality or the condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless wespecifically agree in writing otherwise, we do not accept any liability whatsoever for the performance of the product or for any loss or damage arising out ofthe use of the product. All products supplied and technical advice given is subject to our standard terms and conditions of sale. You should request a copy ofthis document and review it carefully. The information contained in this data sheet is subject to modification from time to time in the light of experience andour policy of continuous development. It is the user's responsibility to verify that this data sheet is current prior to using the product. Brand names mentionedin this data sheet are trademarks of or are licensed to AkzoNobel. | The information in this data sheet is not intended to be exhaustive and is based on the present state of our knowledge and on currentlaws: any person using the product for any purpose other than that specifically recommended in the technical data sheet without firstobtaining written confirmation from us as to the suitability of the product for the intended purpose does so at his own risk. It is always theresponsibility of the user to take all necessary steps to fulfill the demands set out in the local rules and legislation. Always read theMaterial Data Sheet and the Technical Data Sheet for this product if available. All advice we give or any statement made about theproduct by us (whether in this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality orthe condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless we specifically agreein writing otherwise, we do not accept any liability whatsoever for the performance of the product or for any loss or damage arising out ofthe use of the product. All products supplied and technical advice given is subject to our standard terms and conditions of sale. Youshould request a copy of this document and review it carefully. The information contained in this data sheet is subject to modification fromtime to time in the light of experience and our policy of continuous development. It is the user's responsibility to verify that this data sheetis current prior to using the product. Brand names mentioned in this data sheet are trademarks of or are licensed to AkzoNobel. | ||||||||
|
||||||||||
